Vutec ARTSCREEN Surface Hook - Installation Instructions Manual de usuario descargar pdf

VUTEC CORPORATION

www.vutec.com

TEL: (954) 545 9000 - FAX: (954) 545 9011

E-MAIL: [email protected]

INSTALLATION INSTRUCTIONS

Surface Mount Plasma

Installation

The Plasma must be straight and not tilted for the Art Screen to work properly. Tilting of the Plasma is not recommended.

Referring to Figure 2, use a triangle to determine the Plasma

OD onto the wall. Verify the outline accuracy for a problem

free installation.

Determine the depth of the Plasma – from the wall to the

front bezel surface.

Determine the mounting locations for the wall mount

brackets (Figures 1 & 2). Use proper wall anchors (not

supplied) for drywall installation.

Drill pilot holes for #8 screws or install wall anchors as

required.

Install the Art Screen frame (Figure 3) around the Plasma.

Adjust the Art Screen frame so that it is center around the

Plasma. Tighten the screws.

Adjust the depth of the Art Screen frame so that it is 1/2 to

5/8 (Figure 4) inch more than the depth of the Plasma. This

clearance is required for the Art Screen to travel.

Route the motor wires to the backside for connection later.

Wood Frame Installation

A typical wood frame including the liner is approximately 5

inches wide to properly cover the assembly. The wood

overhangs the main shell approximately 3/4 inch when

attached.

Two corner woods are attached to the backside of the

wood frame to take-up the weight.

The wood frame attaches to the main shell by two

clips on the backside (see Picture Frame Installation

and Removal Section) and hold in place by the ears of

the main shell.

Referring to Figure 6, two side panels are provided for

covering the sides of the Art Screen frame. The panels

apply to the frame by Velcro strips supplied.

The Velcro strips are cut to length. Apply the black

part (Hook) of the Velcro to the sides of the frame.

Apply the white part (Loop) of the Velcro to each of

the panels (Figure 6).

Apply the side panels to the Art Screen frame for a

complete installation. The top and bottom of the Art

Screen frame are left open for proper ventilation for

the plasma.

Optionally, custom-made side panels may be installed

as desired.

Figure 2

Outlining the Plasma OD onto Wall

Figure 1

Rear View of Frame

1 2 3 4 5 6 7

Indice de contenidos

Pagina 1 - Surface Mount Plasma

VUTEC CORPORATION www.vutec.com TEL: (954) 545 9000 - FAX: (954) 545 9011 E-MAIL: [email protected] INSTALLATION INSTRUCTIO

Pagina 2 - VUTEC CORPORATION

Electrical Connections The Art Screen comes with IR remote control for operations. It is ready for use; no wiring connections are required. Place the

Pagina 3

3. Send the screen up halfway then stop. Send the screen down to its closed limit. The screen must stop above the desired position. If it is not, re

Pagina 4

Accessories Included Description QTY. Main Shell including Artwork and Motor 1 Side Mount Bracket 2 Wall Mount Bracket 2 Wood Frame (Co

Pagina 5

PICTURE FRAME INSTALLATION & REMOVAL SPILC GNIDILS HTIW The backside of the picture frame is in full contact with the front edges of the metal

Pagina 6

VUTEC CORPORATION www.vutec.com TEL: (954) 545 9000 - FAX: (954) 545 9011 E-MAIL: [email protected]

Pagina 7

DISPLAY PANEL REAR VIEW DISPLAY PANEL WALL INSTALLATION CAUTION: A LOW PROFILE WALL MOUNT BRACKET MUST BE USED FOR THIS APPLICATION INSTALLATIO

Comentarios a estos manuales

Sin comentarios

Vutec ARTSCREEN Surface Hook - Installation Instructions Manual de usuario

Busca en linea o descarga Manual de usuario para Monitores Vutec ARTSCREEN Surface Hook - Installation Instructions. Vutec ARTSCREEN Surface Hook - Installation Instructions User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Monitores Vutec ARTSCREEN Surface Hook - Installation Instructions